Creality K2 Plus Idler Wheel Noise Lubrication Guide

Regular maintenance is the key to keeping your Creality K2 Plus running smoothly and producing accurate prints. One essential task is lubricating the idler wheels to prevent noise, reduce wear, and extend the life of your machine.

This guide covers why lubrication is necessary, how often you should do it, the tools you’ll need, and step-by-step instructions.

Why Lubrication is Necessary The K2 Plus features an all-metal idler structure, which is prone to friction noise and rust over time. Without regular care, this can shorten the lifespan of your equipment and affect print quality.

Anti-rust & Noise Reduction – Lubrication helps prevent corrosion and reduces metal-on-metal noise. Factory Pre-Maintenance – Each K2 Plus receives a basic lubrication treatment before leaving the factory, but continued maintenance is essential for long-term performance. Recommended Maintenance Cycle Frequent Use ：Lubricate once per week Infrequent Use – Lubricate once every two weeks 💡 If you hear abnormal metal friction noises during operation, stop immediately and perform maintenance. You can also refer to the official K2 Plus Periodic Maintenance Tips Wiki page for more detailed schedules.

Lubricant & Filament Specifications Recommended Lubricant: WD-40 Specialist® Silicone

Ensure it has an authentic anti-counterfeiting mark. Safe for use on belts without causing damage. Strictly Prohibited: Non-certified lubricants

These may cause bearing corrosion, steel shaft wear, seal aging, and other failures.

Click here to learn more about WD-40 Specialist® Silicone.

Step by Step Lubrication Procedure Tools You’ll Need Lint-free cloth WD-40 Specialist® Silicone 1. Clean the Idler Wheels Use a lint-free cloth to wipe dust and debris from the idler wheels on the left X-axis assembly (2102013343) and right X-axis assembly (2102013346). Avoid paper towels that may leave fibers. 2. Apply Lubricant to X-axis Idlers Shake the WD-40 Specialist® Silicone well. Spray onto the plastic assembly and wait about 5 seconds for penetration. Manually move the hotend to ensure even lubrication. 1

2

3

4

3. Lubricate Additional Assemblies Repeat the process for:

Left front tension assembly (2102013345) Right front tension assembly (2102013344) X-axis motor assembly (2102013352) Y-axis motor assembly (2102013353) 1

2

3

4

5

6

7

8

4. Clean & Lubricate the X-axis Guide Rail Wipe with a lint-free cloth. Spray WD-40 Specialist® Silicone along the entire rail. See K2 Plus X-axis Guide Rail Cleaning Guide for detailed steps. 5. Clean the Y-axis Lead Screws Over time, sticky black residue may form. Use a PETG-printed lead screw cleaning tool to clamp both sides of the screw. Perform a homing operation to clean (see video). Refer to the K2 Plus Z-axis Lead Screw Cleaning Guide. 6. Final Noise Check Move the hotend manually to confirm the noise is gone. If noise persists, replace the K2 Plus idler module as shown in the Replace K2 Plus Idler Module guide. By following this maintenance guide, you can keep your K2 Plus operating quietly and precisely, ensuring a longer service life and consistently high-quality prints.

For more Creality 3D Printer, you can click the related articles as follows:

⏰Free Gift Offer ends Sep 15.

🎁 Buy SPARKX i7 NANO, Get 2*FREE Hyper PLA RFID!

Creality K2 Plus Idler Wheel Noise Lubrication Guide

Recent News

⏰Free Gift Offer ends Sep 15.

🎁 Buy SPARKX i7 NANO, Get 2*FREE Hyper PLA RFID!

Creality K2 Plus Idler Wheel Noise Lubrication Guide

Recent News

How to Store 3D Printer Filament: Dry Boxes, Bags & Humidity Control

Q & A for Creality KliTek™: The Next-Gen Nozzle-Changer for Multi-Material 3D Printing

How to Clean 3D Printer Nozzle: Tips for Better Prints

Creality Sparkx i7 Consumable Parts Maintenance & Replacement